Home
>> Products
>> MITSUBISHI
>> Servo driver/Servo motor
>> MR-J3 series
>> MR-J3 amplifier
>> MR-J3-10T | MITSUBISHI CC-Link communication driver MR-J3-10T
MR-J3-10T | MITSUBISHI CC-Link communication driver MR-J3-10T
MITSUBISHI MR-J3-10T Manual And Instructions
MR-J3-10T datasheetPDF datasheet
MR-J3-10T CC-LinkINSTRUCTION MANUAL
MR-J3-10T General-Purpose InterfaceINSTRUCTION MANUAL
MITSUBISHI MR-J3-10T Product information and technical parameters：
Brand: MITSUBISHI
Name: CC-Link communication driver
Model: MR-J3-10T
MITSUBISHI motor universal AC servo amplifier MELSERVO-J3 series.
Rated output: 0.1kw.
Interface type: CC-Link communication type (built-in positioning function).
Power specification: single phase AC200V.
Positioning operation by setting position and rotational speed data in the positioning table and receiving the start signal from the main controller.
The setting of the position and speed of the positioning table, as well as the start and stop operation can be completed through CC-Link communication.
By using the MR-J3-D01 extension IO unit, the DI/O instruction can be used to select and locate the table.
(CC-Link can not be used for MR-J3-D01 communications).
With built-in positioning function of the servo amplifier, can be set through the CC-Link communications and speed data. (corresponding to the CC-Link version: Ver.1.10)
Can be achieved through the CC-Link communications to start, stop and monitoring and other operations.
Serial communication reduce wiring.
Distributed servo control system can be built by CC-Link communication.
The parameters of unit MR-PRU03 (optional) the parameter setting, operation and monitoring more convenient.
The servo amplifier can be used for speed control operation.
When the two stations are occupied, the speed can be set directly by the remote register.
...More relevant models >>>>
MR-J3-10T datasheetPDF datasheet
MR-J3-10T CC-LinkINSTRUCTION MANUAL
MR-J3-10T General-Purpose InterfaceINSTRUCTION MANUAL
MITSUBISHI MR-J3-10T Product information and technical parameters：
Brand: MITSUBISHI
Name: CC-Link communication driver
Model: MR-J3-10T
MITSUBISHI motor universal AC servo amplifier MELSERVO-J3 series.
Rated output: 0.1kw.
Interface type: CC-Link communication type (built-in positioning function).
Power specification: single phase AC200V.
Positioning operation by setting position and rotational speed data in the positioning table and receiving the start signal from the main controller.
The setting of the position and speed of the positioning table, as well as the start and stop operation can be completed through CC-Link communication.
By using the MR-J3-D01 extension IO unit, the DI/O instruction can be used to select and locate the table.
(CC-Link can not be used for MR-J3-D01 communications).
With built-in positioning function of the servo amplifier, can be set through the CC-Link communications and speed data. (corresponding to the CC-Link version: Ver.1.10)
Can be achieved through the CC-Link communications to start, stop and monitoring and other operations.
Serial communication reduce wiring.
Distributed servo control system can be built by CC-Link communication.
The parameters of unit MR-PRU03 (optional) the parameter setting, operation and monitoring more convenient.
The servo amplifier can be used for speed control operation.
When the two stations are occupied, the speed can be set directly by the remote register.
The length of the line: 2M.
IP level: IP65.
Bending life: high bending life.
Electric motor power supply cable for HF-KP/HF-MP series (motor shaft with side extraction). The length of the line: 10M.
IP level: IP65.
Direct type.
Bending life: high bending life.
The cable is not shielded.
Electric motor power supply cable for HF-KP/HF-MP series (motor shaft with side extraction) MITSUBISHI MR-J3-10T MR-J3-10T Drive: MR-H_ACN series CC-LINK features.
Rated output: 0.4KW.
The test system is composed of two parts, namely, the servo driver, the motor system and the host computer.
The host computer sends the speed command signal to the servo driver,
Servo drives start to run in accordance with the instructions.
In the course of operation, the running data of the servo system is collected by the host computer and the data acquisition circuit,
And carries on the preservation, the analysis and the display to the data MITSUBISHI MR-J3-10T. Because the motor is not loaded in this test system,
So compared with the previous two kinds of testing systems, the system has a relatively small volume,
And the measurement and control circuit of the system is relatively simple,
But it also makes the system can not simulate the actual operation of the servo drive MITSUBISHI MR-J3-10T.
Usually, such testing system is only used to test the rotational speed and angular displacement of the tested system under no-load condition,
And can not carry on the comprehensive and accurate test to the servo drive. Multi axis integrated servo amplifier.
MITSUBISHI general AC servo amplifier MELSERVO-J4 series.
Axis number: 2 axis.
Rated output A axis (Note 1): 0.2kw.
Rated output B axis (Note 1): 0.2kw.
Interface: SSCNET III /H.
Note the 1:A axis, B axis, C axis indicates the name of a type of multi axis servo amplifier axis. The C axis represents the 3 axis one type servo amplifier.
Support SSCNET III /H. 1 unit can drive 2 servo motor two axis servo amplifier.
More energy saving, space saving, less wiring, low cost MR-J3-10T.
Inherited the high performance and high reliability.
Will, as always, adhere to and uphold the excellent quality of MELSERVO.
MR-J4 has inherited the excellent design of existing prroducts MR-J3-10T.
Its essence to its dregs, create advantage and cost effective utilization rate,
Make full use of renewable resources, to create a new product.
IP level: IP65.
Bending life: high bending life.
Electric motor power supply cable for HF-KP/HF-MP series (motor shaft with side extraction). The length of the line: 10M.
IP level: IP65.
Direct type.
Bending life: high bending life.
The cable is not shielded.
Electric motor power supply cable for HF-KP/HF-MP series (motor shaft with side extraction) MITSUBISHI MR-J3-10T MR-J3-10T Drive: MR-H_ACN series CC-LINK features.
Rated output: 0.4KW.
The test system is composed of two parts, namely, the servo driver, the motor system and the host computer.
The host computer sends the speed command signal to the servo driver,
Servo drives start to run in accordance with the instructions.
In the course of operation, the running data of the servo system is collected by the host computer and the data acquisition circuit,
And carries on the preservation, the analysis and the display to the data MITSUBISHI MR-J3-10T. Because the motor is not loaded in this test system,
So compared with the previous two kinds of testing systems, the system has a relatively small volume,
And the measurement and control circuit of the system is relatively simple,
But it also makes the system can not simulate the actual operation of the servo drive MITSUBISHI MR-J3-10T.
Usually, such testing system is only used to test the rotational speed and angular displacement of the tested system under no-load condition,
And can not carry on the comprehensive and accurate test to the servo drive. Multi axis integrated servo amplifier.
MITSUBISHI general AC servo amplifier MELSERVO-J4 series.
Axis number: 2 axis.
Rated output A axis (Note 1): 0.2kw.
Rated output B axis (Note 1): 0.2kw.
Interface: SSCNET III /H.
Note the 1:A axis, B axis, C axis indicates the name of a type of multi axis servo amplifier axis. The C axis represents the 3 axis one type servo amplifier.
Support SSCNET III /H. 1 unit can drive 2 servo motor two axis servo amplifier.
More energy saving, space saving, less wiring, low cost MR-J3-10T.
Inherited the high performance and high reliability.
Will, as always, adhere to and uphold the excellent quality of MELSERVO.
MR-J4 has inherited the excellent design of existing prroducts MR-J3-10T.
Its essence to its dregs, create advantage and cost effective utilization rate,
Make full use of renewable resources, to create a new product.
...More relevant models >>>>
Last one: MITSUBISHI For direct drive servo motor drive MR-J3-22KB-RJ080W
next one: MITSUBISHI CC-Link communication driver MR-J3-20T
Related download