Home
>> Products
>> MITSUBISHI
>> Q series PLC
>> Base Board
>> Extended backplane cable
>> QC50B | MITSUBISHI Extension cable QC50B
QC50B | MITSUBISHI Extension cable QC50B
MITSUBISHI QC50B Manual And Instructions
QC50B datasheetPDF datasheet
QC50B datasheetPDF datasheet
MITSUBISHI QC50B Product information and technical parameters：
Brand: MITSUBISHI
Name: Extension cable
Model: QC50B
Cable length 5 meters.
Extended substrate for connection.
...More relevant models >>>>
QC50B datasheetPDF datasheet
QC50B datasheetPDF datasheet
MITSUBISHI QC50B Product information and technical parameters：
Brand: MITSUBISHI
Name: Extension cable
Model: QC50B
Cable length 5 meters.
Extended substrate for connection.
"Maximum control axis: 16 axis.
Connection mode with servo amplifier: SSCNET III /H connection type.
The maximum distance between the drive units: 100m.
Operation cycle: 0.88ms, 1.77ms.
Interpolation function: linear interpolation (maximum 4 axis), 2 axis arc interpolation.
Color signal: 4 points.
Color detecting set: 16 set MITSUBISHI QC50B.
Even the long distance wiring can be flexible.
The use of fiber optic cable, with high speed, high performance, high reliability of the servo system controller network QC50B
In addition to the traditional positioning control, but also to support speed / torque control and synchronous control.
Use simple movement module setup tool",
Can easily perform positioning settings, monitoring and debugging, etc MITSUBISHI QC50B. .
In addition, the data can be collected and displayed synchronously with the motion controller.
SSCNET III /H connection to save the wiring, the maximum distance between the station up to 100m,
Absolute position system can be easily supported.
The upper limit limit switch, the lower limit switch and the near point block signal are input by the servo amplifier,
Thus greatly reducing wiring MITSUBISHI QC50B.
In addition to positioning control and speed control, but also to perform synchronization control, cam control, torque control, touch pressure control, etc..
Positioning module (QD75MH) of the project and the sequence of the previous model is highly compatible with the old model,
The project can be easily applied to the simple motion module (QD77MS). "Connect to read and write 1Ch.
ID system interface module.
ID controller M-688-001/002 BIS can be installed directly to the Q series of substrates,
Control module for reading and writing ID tag data through a programmable logic controller.
The ladder ddiagram of M-688-002 BIS is compatible with QD35ID1/2 QC50B.
2 antennas can be connected, and the parallel processing of the 2 channels can be simultaneously carried out.
Can use all ID tags in the M BIS series.
ID series /BIS system is an industriaal automation ID system which can use the electromagnetic combination method to read and write data QC50B.
ID tag has a variety of sizes and storage capacity.
Connection mode with servo amplifier: SSCNET III /H connection type.
The maximum distance between the drive units: 100m.
Operation cycle: 0.88ms, 1.77ms.
Interpolation function: linear interpolation (maximum 4 axis), 2 axis arc interpolation.
Color signal: 4 points.
Color detecting set: 16 set MITSUBISHI QC50B.
Even the long distance wiring can be flexible.
The use of fiber optic cable, with high speed, high performance, high reliability of the servo system controller network QC50B
In addition to the traditional positioning control, but also to support speed / torque control and synchronous control.
Use simple movement module setup tool",
Can easily perform positioning settings, monitoring and debugging, etc MITSUBISHI QC50B. .
In addition, the data can be collected and displayed synchronously with the motion controller.
SSCNET III /H connection to save the wiring, the maximum distance between the station up to 100m,
Absolute position system can be easily supported.
The upper limit limit switch, the lower limit switch and the near point block signal are input by the servo amplifier,
Thus greatly reducing wiring MITSUBISHI QC50B.
In addition to positioning control and speed control, but also to perform synchronization control, cam control, torque control, touch pressure control, etc..
Positioning module (QD75MH) of the project and the sequence of the previous model is highly compatible with the old model,
The project can be easily applied to the simple motion module (QD77MS). "Connect to read and write 1Ch.
ID system interface module.
ID controller M-688-001/002 BIS can be installed directly to the Q series of substrates,
Control module for reading and writing ID tag data through a programmable logic controller.
The ladder ddiagram of M-688-002 BIS is compatible with QD35ID1/2 QC50B.
2 antennas can be connected, and the parallel processing of the 2 channels can be simultaneously carried out.
Can use all ID tags in the M BIS series.
ID series /BIS system is an industriaal automation ID system which can use the electromagnetic combination method to read and write data QC50B.
ID tag has a variety of sizes and storage capacity.
...More relevant models >>>>
Last one: 
next one: Related download