Q2ASHCPU-S1 | MITSUBISHI CPU unit Q2ASHCPU-S1

Q2ASHCPU-S1 Introduce | Q2ASHCPU-S1 Catalog / Manual / Instructions / Software download

MITSUBISHI Q2ASHCPU-S1 Manual And Instructions
Q2ASHCPU-S1 datasheetPDF datasheet
Q2ASHCPU-S1 General Instruction Manual
Q2ASHCPU-S1 User's Manual
Q2ASHCPU-S1 HardwareUser's Manual
Q2ASHCPU-S1 User's Manual
Q2ASHCPU-S1 HardwareUser's Manual
Q2ASHCPU-S1 PID Control InstructionsProgramming Manual

MITSUBISHI Q2ASHCPU-S1 Product information and technical parameters：
Brand: MITSUBISHI
Name: CPU unit
Model: Q2ASHCPU-S1
Input and output points: 1024 points.
Input / output data points: 8192 points.
Program capacity: 60k.
Basic command processing speed (LD command) S:0.075.
PLC in the program execution stage: according to the order of the user program order to store the order of each instruction,
After the corresponding operation and processing, the result is written to the output status register,
The contents of the output status register are changed with the execution of the program.
Output refresh phase: when all instructions are executed,
The output status register is sent to the output latch in the output refresh stage,
And through a certain way (relay, transistor or transistor) output, drive the corresponding output equipment.

Capable of continuous thermocouple or platinum temperature measurement.
In addition, the temperature measurement range can be set with the use of the temperature.
The length of time required to execute the instruction, the length of the user''s program, the type of instruction, and the speed of the CPU execution are very significant,
Generally, a scanning process, the fault diagnosis time,
Communication time, input sampling and output refresh time is less,
The execution time is accounted for the vast majority of MITSUBISHI Q2ASHCPU-S1 Q2ASHCPU-S1
The response time of PLC is the interval between the time of the change of the external output signal of the PLC and the time of the change of the external output signal which is controlled by it,
Lag time, this is the time constant of the input circuit,
The time constant of the output circuit, the arrangement of the user statement and the use of the instruction,
The cycle scan mode of PLC and the way of PLC to refresh the I/O and so on MITSUBISHI Q2ASHCPU-S1.
This phenomenon is called the I/O delay time effect. Enter 32 points.
5mA DC24V.
Response time: 0.3ms.
32 point 1 public.
Output 32 points MITSUBISHI Q2ASHCPU-S1.
DC12/24V.
Leakage current: 0.1mA OFF.
Response time: 1ms. 32 point 1 public.
Protection function.
Surge.
40 pin connector.
Switching value, also known as logic, refers to only two values, 0 or 1, ON or OFF.
It is the most common control, it is the advantage of PLC control,
Is also the most basic application of PLC.
Switch volume control is designed to,
According to the current input combination of the switch quantity and the history of the input sequence,
So that PLC generates the corresponding switching output,
In order to make the system work in a certain order.
So, sometimes also known as the order control.
And sequential control is divided into manual, semi-automatic or automatic.
And the control principle is decentralized, centralized and hybrid control threee Q2ASHCPU-S1. 8 channel analog input module.
This is a high density of 8 channel A/D components,
Can receive voltage and current input, with the installation of the inside of the cover plate switch,
The input type and range of each channel can be sset up according to the application requirements:
12 bit resolution,
Automatic drift correction function,
0 Q2ASHCPU-S1. 5msec/1 channel,
-10-0-10V or 0-20mA input.

...More relevant models >>>>