MITSUBISHI
Home >> Products >> MITSUBISHI >> FX series PLC >> FX3S series >> FX3S-10MT/DSS | MITSUBISHI PLC FX3S-10MT/DSS

FX3S-10MT/DSS | MITSUBISHI PLC FX3S-10MT/DSS

MITSUBISHI FX3S-10MT/DSS Manual And Instructions
FX3S-10MT/DSS datasheetPDF datasheet

MITSUBISHI FX3S-10MT/DSS Product information and technical parameters:
Brand: MITSUBISHI
Name: PLC
Model: FX3S-10MT/DSS
Input and output points: 10 points.
Power supply: DC24V.
Input points: 6 points.
Output points: 4 points.
Output form: transistor output (source).
Power consumption: 6W.
Weight: 0.22KG.
Outline dimension: 60x90x49mm.
Built in CPU, power supply, input and output.
Keep FX1S compact body, while adding more features.
Special adaptor and function expansion board can be installed and used FX3 series.
High speed operation.
Basic instructions: 0.21 s/ instruction
Application instruction: 0.5 s/ instruction
Large capacity memory.
Built in program memory 4000 steps.
No battery.
Auxiliary relay: 1536 points.
Timer: 138 points.
Counter: 67.
Data register: 3000.
A new application model.
FX3SA is a basic model on the basis of the basic performance of the FX1S increased the expansion of the new models.
FX3SA is suitable for all kinds of fields, such as analog quantity, Ethernet, MODBUS function, small scale equipment and so on.
Basic models suitable for small scale control.
Compact but powerful,
At the same time, the analog quantity and the communication function and so on.

Total input and output points: 40 points.
Input points: 24 points.
Output points: 16 points.
Output type: relay output.
Power supply voltage: DC24V.
Input signal voltage: DC24V.
8K capacity of the RAM memory, the maximum can be extended to 16K.
CPU arithmetic processing speed of 0.08 S/ basic instructions MITSUBISHI FX3S-10MT/DSS.
On the right side of the FX2N series can be connected to the input and output expansion modules and special function modules FX3S-10MT/DSS
The basic unit is built in the 2 axis independent maximum 20kHz positioning function (transistor output type).
Quick disconnect the terminal block, which adopts excellent maintainability to quickly disconnect the terminal blocks, even if the cable is then replaced by the cable MITSUBISHI FX3S-10MT/DSS.
Clock function and hour meter function, all of the PLC FX2N has a real-time clock standard.
Continuous scanning function, to define the operation cycle for the application of the continuous scan time.
Input filter adjustment function, you can use the input filter to smooth the input signal (in the basic unit x000 to x017).
Note recording function, Component annotation can be recorded in the program register MITSUBISHI FX3S-10MT/DSS.
Online program editor, online change the program will not lose the working hours or stop production operation.
RUN/STOP switch, running on panel / stop switch easy to operate.
Remote maintenance, remote programming software can monitor, upload or uninstall programs and data via modem communications
Password protection, using a eight digit password to protect your program. Function extension board for RS-232C communication.
No DC24V consumption, do not take up input and output. Axis of control: 1.
Interpolation: No.
Program memory: built-in 3.8k step EEPROM.
Applicable PLC:FX1N, FX2N, FX3U, FX2NC (to FX2NC-CNV-IF).
Applicable PLC:FX3UC (to FX2NC-CNV-IF or FX3UC-1PS-5V).
Not only can deal with single speed positioning and positioning,
Can also carry on the multi section fast operation and so on complex control.
Can not be connected to the PLC, while running alone.
1 can control 1 axes,
FX1N, FX2N, PLC FX3U up to 8 uunits can be connected,
PLC FX2NC up to 4 units can be connected,
FX3UC PLC can connect up to 7 units, and a plurality of shafts can be independently controlled FX3S-10MT/DSS.
Can output up to 200kHz of the pulse train.
The connection function of thhe absolute position detection function and the manual pulse generator FX3S-10MT/DSS.
Can be used in the form of flow chart programming software, visual programming.


...More relevant models >>>>