Brand sort
MITSUBISHI A0J2-C214-S1 Market price | A0J2-C214-S1 Introduction
next one: 
Last one: MITSUBISHI A0J2-C214-S1
Power: 15kw.
Purpose: high frequency braking resistor.
The use rate of the built-in regenerative brake of the transducer can be promoted.
When using the FR-ABR type brake resistor, the short circuit piece between the terminal PR-PX is removed. Does not remove the short circuit chip will lead to overheating of the brake resistor.
The utilization rate of the regenerative braking should be less than the allowable brake use rate in the above table A0J2-C214-S1
With the operating frequency of the brake resistor to reach 300 degrees C or higher, it is necessary to take protective measures and cooling.
MYS type resistor can be used. But please pay attention to the allowable brake use rate.
Do not remove the terminal P/+ and P1 between the short circuit chip, in addition to connecting the DC reactor.
The installation of thermal relay, to avoid overheating and burn the braking resistor. Extended power supply for CPU module with built-in power supply.
Bus conversion module is required when using. Maximum can be connected to 2 sets. Drive: MR-H_ACN series CC-LINK features.
Rated output: 0.1KW.
The test system is composed of two parts, namely, the servo driver, the motor system and the host computer.
The host computer sends the speed command signal to the servo driver,
Servo drives start to run in accordance with the instructions.
In the course of operation, the running data of the servo system is collected by the host computer and the data acquisition circuit,
And carries on the preservation, the analysis and the display to the data. Because the motor is not loaded in this test system,
So compared with the previous two kinds of testing systems, the system has a relatively small volume,
And the measurement and control circuit of the system is relatively simple,
But it also makes the system can not simulate the actual operation of the servo drive.
Usually, such testing system is only used to test the rotational speed and angular displacement of the tested system under no-load condition,
And can not carry on the comprehensive and accurate test to the servo drive.
A0J2-C214-S1 Operation manual / Instructions / Catalog download link: /searchDownload.html?Search=A0J2-C214-S1&select=5
Purpose: high frequency braking resistor.
The use rate of the built-in regenerative brake of the transducer can be promoted.
When using the FR-ABR type brake resistor, the short circuit piece between the terminal PR-PX is removed. Does not remove the short circuit chip will lead to overheating of the brake resistor.
The utilization rate of the regenerative braking should be less than the allowable brake use rate in the above table A0J2-C214-S1
With the operating frequency of the brake resistor to reach 300 degrees C or higher, it is necessary to take protective measures and cooling.
MYS type resistor can be used. But please pay attention to the allowable brake use rate.
Do not remove the terminal P/+ and P1 between the short circuit chip, in addition to connecting the DC reactor.
The installation of thermal relay, to avoid overheating and burn the braking resistor. Extended power supply for CPU module with built-in power supply.
Bus conversion module is required when using. Maximum can be connected to 2 sets. Drive: MR-H_ACN series CC-LINK features.
Rated output: 0.1KW.
The test system is composed of two parts, namely, the servo driver, the motor system and the host computer.
The host computer sends the speed command signal to the servo driver,
Servo drives start to run in accordance with the instructions.
In the course of operation, the running data of the servo system is collected by the host computer and the data acquisition circuit,
And carries on the preservation, the analysis and the display to the data. Because the motor is not loaded in this test system,
So compared with the previous two kinds of testing systems, the system has a relatively small volume,
And the measurement and control circuit of the system is relatively simple,
But it also makes the system can not simulate the actual operation of the servo drive.
Usually, such testing system is only used to test the rotational speed and angular displacement of the tested system under no-load condition,
And can not carry on the comprehensive and accurate test to the servo drive.
A0J2-C214-S1 Operation manual / Instructions / Catalog download link: /searchDownload.html?Search=A0J2-C214-S1&select=5
...more relevant model market price >>>>
Related products
MITSUBISHI
Connecting cable
A0J2-C01
Cale for unit load.
Length: 80mm.
Input
MITSUBISHI
Computer connection module
A0J2-C214-S1
RS-232C 1 channel, RS-422 1 channel.
Tra
MITSUBISHI
Connecting cable
A0J2-C04B
A65B/A68B/A55B/A58B connection cale.
Le
MITSUBISHI
Connecting cable
A0J2-C03F
A0J2 56.
Input / output unit 2
MITSUBISH