MITSUBISHI
Home >> Download >> MITSUBISHI >> Manual Download >> MITSUBISHI FX1S-10MR-D Manual FX1S-10MR-D PROGRAMMING MANUAL II

MITSUBISHI FX1S-10MR-D Manual FX1S-10MR-D PROGRAMMING MANUAL II

Brand: MITSUBISHI
Product model: FX1S-10MR-D
Name: PLC
Sort: PROGRAMMING MANUAL II
File language: English
File size: 7.09MB
Input signal power: 40mA. DC24V
Axis of control: 1.
Output frequency: Max 200kHz.
Weight: 0.2kg.
FX3U-1PG is a pulse output module of the maximum output 200kHz pulse train.
7 operation modes needed to take the simple position control.
The speed and the target address can be changed in the positioning operation according to the operation of the project,
Support near S shape plus deceleration FX1S-10MR-D Manual FX1S-10MR-D PROGRAMMING MANUAL II FX1S-10MR-D High speed positioning can be carried out smoothly.
Up to 8 units can be connected to FX3U or FX3UC.
Connecting FX3UC requires FX2NC-CNV-IF or FX3UC-IPS-5V. Function: input / output module (internal service power supply).
Input / output points: 32 points
Input points: 16 points.
Output points: 16 points FX1S-10MR-D Manual FX1S-10MR-D PROGRAMMING MANUAL II.
DC5V internal consumption current: 965mA.
DC24V internal consumption current: 250mA.
Input / output mode: DC input (drain / source) / transistor (drain).
In order to extend the input output of the device.
Also has a built-in power supply products.
The maximum number of points for the input and output is 256.
Expansion module: up to 16 units (in addition to the power expansion module)
The total number of CC-Link, AnyWireASLINK, and Bitty series of remote I/O is 512 points FX1S-10MR-D Manual FX1S-10MR-D PROGRAMMING MANUAL II. Application: you can transfer the same image data at a high speed (about two seconds per 64KB data) to multiple F940GOT.
When programming software is used in the case of Designer2 GT,
You can create a file in HEX Intel format.
Using communication software to transfer data to a ROM writer.
Application Series: F940GOT. "MITSUBISHI inverter FR-F720P series.
Voltage level: three phase 200V.
Frequency converter capacity: 18.5KW.
When the inverter is running, the starting current and starting torque of the motor are how?
With the operation of the inverter, with the acceleration of the motor to improve the frequency and voltage,
The starting current is limited to 150% below the rated current (according to the different types of aircraft, 125%~200%).
It is based on the overall effect of three-phase waveform generation,
In order to approach the ideal circular rotating magnetic field in the air gap of the motor,
A generation phase modulation waveform control inscribesthe polygon to approach the circle way.
After practice, it has been improved, that is, the introduction of frequency compensation, can eliminate the error of speed control;
By feedback estimation of flux amplitude, eliminating the influence of stator resistance at low speed, the output voltage and current closed loop,
In order to improve the accuracy and stability of the dynamic.
But there are many control circuit, and no torque is introduced, so the system performance has not been improved.
Frequency converter is a power control device which uses the power of the power semiconductor device to change the power frequency to another frequency,
Can realize the asynchronous motor soft start, variable frequency speed regulation, improve the operation precision, change the power factor, over current / over voltage / overload protection and other functions.
The use of frequency converter motor is in order to speed, and reduce the starting current.
In order to produce a variable voltage and frequency,
The equipment to the power of the AC power conversion to DC (DC), the process is called rectification.
The direct current (DC) is transformed into alternating current (AC) and its scientific term is "inverter" (inverter).
General inverter is the DC power supply inverter for a certain fixed frequency and a certain voltage of the inverter.
For the inverter as the frequency adjustable, adjustable voltage inverter, we called the inverter.
Inverter output waveform is simulated sine wave,
Is mainly used in three-phase asynchronous motor speed control, and also called frequency governor.
For the variable frequency inverter, which is mainly used in the testing equipmeent of instrument and meter,
To sort out the waveform, you can output the standard sine wave, called the inverter power supply FX1S-10MR-D Manual FX1S-10MR-D PROGRAMMING MANUAL II.
The general inverter is 1520 times inverter price.
The main device called "inverter" because of the voltage or frequency of the inverter device ",
Therefore, the product itself is named "inverter", that is: inverter FX1S-10MR-D Manual FX1S-10MR-D PROGRAMMING MANUAL II. "
Related products
MITSUBISHI
PLC
FX1S-10MR-001
MITSUBISHI PLC FX1S-10MR-001
Total points: 10 points. Input points: 6 poin
MITSUBISHI
PLC
FX1S-30MT-001
MITSUBISHI PLC FX1S-30MT-001
Total points: 30 points. Input points: 16 poi
MITSUBISHI
PLC
FX1S-30MT-ESS/UL
MITSUBISHI PLC FX1S-30MT-ESS/UL
Max input / output points: 30 points. Supply
MITSUBISHI
PLC
FX1S-20MT-ESS/UL
MITSUBISHI PLC FX1S-20MT-ESS/UL
Max input / output points: 20 points. Supply