Home
>> Products
>> MITSUBISHI
>> Servo driver/Servo motor
>> MR-J2S series
>> MR-J2S servo driver
>> MR-J2S-60CP-S084 | MITSUBISHI Built in positioning function servo amplifier MR-J2S-60CP-S084
MR-J2S-60CP-S084 | MITSUBISHI Built in positioning function servo amplifier MR-J2S-60CP-S084
MITSUBISHI MR-J2S-60CP-S084 Manual And Instructions
MR-J2S-60CP-S084 datasheetPDF datasheet
MR-J2S-60CP-S084 Instruction Manual
MITSUBISHI MR-J2S-60CP-S084 Product information and technical parameters：
Brand: MITSUBISHI
Name: Built in positioning function servo amplifier
Model: MR-J2S-60CP-S084
"MITSUBISHI general purpose AC servo amplifier MELSERVO-J2-Super series.
Rated output: 0.6kw.
Built in positioning function.
Voltage: 3 phase AC200VAC or single phase AC230V.
Compatible with "MR-J2S- CP-S084" - servo amplifier and interface unit "MR-J2S-TO1" positioning by CC-Link
Simply setting the point table.
AC servo can be used as the driving source of the field network.
Using servo amplifier built-in positioning function, position data and speed data, you can set the CC-Link.
Start, stop and display can also be transmitted through the CC-Link.
Serial communication reduces wiring.
AC servo distributed control system can be easily constructed. "
...More relevant models >>>>
MR-J2S-60CP-S084 datasheetPDF datasheet
MR-J2S-60CP-S084 Instruction Manual
MITSUBISHI MR-J2S-60CP-S084 Product information and technical parameters：
Brand: MITSUBISHI
Name: Built in positioning function servo amplifier
Model: MR-J2S-60CP-S084
"MITSUBISHI general purpose AC servo amplifier MELSERVO-J2-Super series.
Rated output: 0.6kw.
Built in positioning function.
Voltage: 3 phase AC200VAC or single phase AC230V.
Compatible with "MR-J2S- CP-S084" - servo amplifier and interface unit "MR-J2S-TO1" positioning by CC-Link
Simply setting the point table.
AC servo can be used as the driving source of the field network.
Using servo amplifier built-in positioning function, position data and speed data, you can set the CC-Link.
Start, stop and display can also be transmitted through the CC-Link.
Serial communication reduces wiring.
AC servo distributed control system can be easily constructed. "
Servo motor series: flat type, medium capacity.
Rated output: 2.0kw.
Rated speed; 2000r/min.
Electromagnetic brake: No.
Power supply: 200V.
The most suitable medium capacity, flat type products to limit the installation space of the situation.
Improve the environmental performance of HG-KR, HG-MR, HG-RR, HG-UR series of products using IP65 MITSUBISHI MR-J2S-60CP-S084.
100 scene, there are 100 different drive control MR-J2S-60CP-S084
In order to meet the needs of the diverse and detailed field,
MR-J4 product line configuration, providing a wealth of servo amplifier and servo motor products.
Can meet the different needs of different customers. Motor series: low inertia, medium power.
Rated output power: 8.0kw.
Rated speed: 1000r/min.
Whether to bring the brakes: with MITSUBISHI MR-J2S-60CP-S084.
Shaft end: Standard (straight).
Voltage: 400V type.
Protection level: IP65 (IP67).
Features: low inertia from low speed to high speed, three modes can be selected, suitable for different application range. As a standard port, 30KW or greater power is suitable for flange (type) installation and support foot mounting.
Application example: injection molding machine, semiconductor manufacturing equipment, large conveyor machinery MITSUBISHI MR-J2S-60CP-S084.
High resolution encoder 131072p/rev (17 bit).
The encoder with high resolution ensures excellent performance and stability at low speed.
All motor dimensions are the same as before and all are compatible with the wiring. Drive: MR-H_ACN series CC-LINK features.
Rated output: 0.6KW.
The test system is composed of two parts, namely, the servo driver, the motor system and the host computer.
The host computer sends the speed command signal to the servo driver,
Servo drives start to run in accordance with the instructions.
In the course of operation, the running data of the servo system is collected by the host computer and the data acquisition circuit,
And carries on the preservation, the analysis and the display to the data. Because the motor is not loaded in this test system,
So compared with the previous two kinds of testing systems, the system has a relatively small volume,
And the measurement and control circuit of the system is relatively simple,
But it also makes the system can not simulate the actual operation of the servo drive MR-J2S-60CP-S084.
Usually, such testing system is only used to test the rotational speeed and angular displacement of the tested system under no-load condition,
And can not carry on the comprehensive and accurate test to the servo drive MR-J2S-60CP-S084.
Rated output: 2.0kw.
Rated speed; 2000r/min.
Electromagnetic brake: No.
Power supply: 200V.
The most suitable medium capacity, flat type products to limit the installation space of the situation.
Improve the environmental performance of HG-KR, HG-MR, HG-RR, HG-UR series of products using IP65 MITSUBISHI MR-J2S-60CP-S084.
100 scene, there are 100 different drive control MR-J2S-60CP-S084
In order to meet the needs of the diverse and detailed field,
MR-J4 product line configuration, providing a wealth of servo amplifier and servo motor products.
Can meet the different needs of different customers. Motor series: low inertia, medium power.
Rated output power: 8.0kw.
Rated speed: 1000r/min.
Whether to bring the brakes: with MITSUBISHI MR-J2S-60CP-S084.
Shaft end: Standard (straight).
Voltage: 400V type.
Protection level: IP65 (IP67).
Features: low inertia from low speed to high speed, three modes can be selected, suitable for different application range. As a standard port, 30KW or greater power is suitable for flange (type) installation and support foot mounting.
Application example: injection molding machine, semiconductor manufacturing equipment, large conveyor machinery MITSUBISHI MR-J2S-60CP-S084.
High resolution encoder 131072p/rev (17 bit).
The encoder with high resolution ensures excellent performance and stability at low speed.
All motor dimensions are the same as before and all are compatible with the wiring. Drive: MR-H_ACN series CC-LINK features.
Rated output: 0.6KW.
The test system is composed of two parts, namely, the servo driver, the motor system and the host computer.
The host computer sends the speed command signal to the servo driver,
Servo drives start to run in accordance with the instructions.
In the course of operation, the running data of the servo system is collected by the host computer and the data acquisition circuit,
And carries on the preservation, the analysis and the display to the data. Because the motor is not loaded in this test system,
So compared with the previous two kinds of testing systems, the system has a relatively small volume,
And the measurement and control circuit of the system is relatively simple,
But it also makes the system can not simulate the actual operation of the servo drive MR-J2S-60CP-S084.
Usually, such testing system is only used to test the rotational speeed and angular displacement of the tested system under no-load condition,
And can not carry on the comprehensive and accurate test to the servo drive MR-J2S-60CP-S084.
...More relevant models >>>>
Last one: MITSUBISHI Built in positioning function servo amplifier MR-J2S-60CP
next one: MITSUBISHI Built in program type operational function servo amplifier MR-J2S-60CL
Related download