Home
>> Products
>> MITSUBISHI
>> Servo driver/Servo motor
>> MR-J2S series
>> MR-J2S servo driver
>> MR-J2S-100B4 | MITSUBISHI SSCNET interface servo amplifier MR-J2S-100B4
MR-J2S-100B4 | MITSUBISHI SSCNET interface servo amplifier MR-J2S-100B4
MITSUBISHI MR-J2S-100B4 Manual And Instructions
MR-J2S-100B4 datasheetPDF datasheet
MR-J2S-100B4 SUPPLEMENTARY INSTRUCTION MANUAL
MITSUBISHI MR-J2S-100B4 Product information and technical parameters：
Brand: MITSUBISHI
Name: SSCNET interface servo amplifier
Model: MR-J2S-100B4
MITSUBISHI general purpose AC servo amplifier MELSERVO-J2-Super series.
Rated output: 1.0kw.
SSCNET interface.
Voltage: 3 phase AC400V.
Complete synchronization system with SSCNET high speed serial communication,
The communication cycle between the controller and the servo amplifier is the longest 0.888ms.
Such systems will be able to provide high reliability and high performance.
When connecting the servo system with SSCNET,
In the motion system, the parameters of the servo amplifier and the acquisition of the data will be displayed on the motion controller.
Connect a dedicated cable with an amplifier and a controller to form a SSCNET system.
This simple connection method reduces the routing time and helps to prevent noise.
Even in the MELSERVO-J2-SUPER series products using high resolution coding standards, the command frequency is no limit.
It is only necessary to add a battery on the servo amplifier, which can form the absolute value system.
Currently there are more than 1000000 high reliability SSCNET servo amplifier networks in use.
...More relevant models >>>>
MR-J2S-100B4 datasheetPDF datasheet
MR-J2S-100B4 SUPPLEMENTARY INSTRUCTION MANUAL
MITSUBISHI MR-J2S-100B4 Product information and technical parameters：
Brand: MITSUBISHI
Name: SSCNET interface servo amplifier
Model: MR-J2S-100B4
MITSUBISHI general purpose AC servo amplifier MELSERVO-J2-Super series.
Rated output: 1.0kw.
SSCNET interface.
Voltage: 3 phase AC400V.
Complete synchronization system with SSCNET high speed serial communication,
The communication cycle between the controller and the servo amplifier is the longest 0.888ms.
Such systems will be able to provide high reliability and high performance.
When connecting the servo system with SSCNET,
In the motion system, the parameters of the servo amplifier and the acquisition of the data will be displayed on the motion controller.
Connect a dedicated cable with an amplifier and a controller to form a SSCNET system.
This simple connection method reduces the routing time and helps to prevent noise.
Even in the MELSERVO-J2-SUPER series products using high resolution coding standards, the command frequency is no limit.
It is only necessary to add a battery on the servo amplifier, which can form the absolute value system.
Currently there are more than 1000000 high reliability SSCNET servo amplifier networks in use.
Motor series: low inertia, medium power.
Rated output power: 7.0kw.
Rated speed: 1500r/min.
Whether to bring the brakes: with.
Shaft end: Standard (straight).
Protection level: IP65 (IP67).
Features: low inertia from low speed to high speed, three modes can be selected, suitable for different application range MITSUBISHI MR-J2S-100B4. As a standard port, 30KW or greater power is suitable for flange (type) installation and support foot mounting MR-J2S-100B4
Application example: injection molding machine, semiconductor manufacturing equipment, large conveyor machinery.
High resolution encoder 131072p/rev (17 bit).
The encoder with high resolution ensures excellent performance and stability at low speed.
All motor dimensions are the same as before and all are compatible with the wiring MITSUBISHI MR-J2S-100B4. The length of the line: 20M.
Relay type.
IP level: IP20.
Bending life: standard.
Encoder with cable (amplifier side); for HF-KP/HF-MP series. Servo motor series: ultra low inertia, low power.
Rated output: 0.4kw.
Rated speed: 3000r/min.
Electromagnetic brake: No.
Shaft end specification: Standard (straight axis).
Features: ultra low inertia is very suitable for high frequency operation MITSUBISHI MR-J2S-100B4.
IP level: IP65.
Application example:
1, insert machine.
2, assembly machinery.
Rotary servo motor.
Numerous motor series and wide motor power range can be used to meet different applications.
The protection level of the HF-KP/HF-MP/HC-LP/HC-RP/HC-UP servo motor to improve the environmental safety is IP65 (except the shaft part). Drive: MR-H_ACN series CC-LINK features.
Rated output: 2.0KW.
The test system is composed of two parts, namely, the servo driver, the motor system and the host computer.
The host computer sends the speed command signal to the servo driver,
Servo drives start to run in accordance with the instructions.
In the course of operation, the running data of the servo system is collected by the host computer and the data acquisition circuit,
And carries on the preservation, the analysis and the display to the data. Because the motor is not loaded in this test system,
So compared with the previous two kinds of testing systems, the system has a relatively small voluume,
And the measurement and control circuit of the system is relatively simple,
But it also makes the system can not simulate the actual operation of the servo drive MR-J2S-100B4.
Usually, such testing system is only used to test the rotational speeed and angular displacement of the tested system under no-load condition,
And can not carry on the comprehensive and accurate test to the servo drive MR-J2S-100B4.
Rated output power: 7.0kw.
Rated speed: 1500r/min.
Whether to bring the brakes: with.
Shaft end: Standard (straight).
Protection level: IP65 (IP67).
Features: low inertia from low speed to high speed, three modes can be selected, suitable for different application range MITSUBISHI MR-J2S-100B4. As a standard port, 30KW or greater power is suitable for flange (type) installation and support foot mounting MR-J2S-100B4
Application example: injection molding machine, semiconductor manufacturing equipment, large conveyor machinery.
High resolution encoder 131072p/rev (17 bit).
The encoder with high resolution ensures excellent performance and stability at low speed.
All motor dimensions are the same as before and all are compatible with the wiring MITSUBISHI MR-J2S-100B4. The length of the line: 20M.
Relay type.
IP level: IP20.
Bending life: standard.
Encoder with cable (amplifier side); for HF-KP/HF-MP series. Servo motor series: ultra low inertia, low power.
Rated output: 0.4kw.
Rated speed: 3000r/min.
Electromagnetic brake: No.
Shaft end specification: Standard (straight axis).
Features: ultra low inertia is very suitable for high frequency operation MITSUBISHI MR-J2S-100B4.
IP level: IP65.
Application example:
1, insert machine.
2, assembly machinery.
Rotary servo motor.
Numerous motor series and wide motor power range can be used to meet different applications.
The protection level of the HF-KP/HF-MP/HC-LP/HC-RP/HC-UP servo motor to improve the environmental safety is IP65 (except the shaft part). Drive: MR-H_ACN series CC-LINK features.
Rated output: 2.0KW.
The test system is composed of two parts, namely, the servo driver, the motor system and the host computer.
The host computer sends the speed command signal to the servo driver,
Servo drives start to run in accordance with the instructions.
In the course of operation, the running data of the servo system is collected by the host computer and the data acquisition circuit,
And carries on the preservation, the analysis and the display to the data. Because the motor is not loaded in this test system,
So compared with the previous two kinds of testing systems, the system has a relatively small voluume,
And the measurement and control circuit of the system is relatively simple,
But it also makes the system can not simulate the actual operation of the servo drive MR-J2S-100B4.
Usually, such testing system is only used to test the rotational speeed and angular displacement of the tested system under no-load condition,
And can not carry on the comprehensive and accurate test to the servo drive MR-J2S-100B4.
...More relevant models >>>>
Last one: MITSUBISHI SSCNET interface servo amplifier MR-J2S-100B
next one: MITSUBISHI Built in positioning function servo amplifier MR-J2S-100CP
Related download