Home
>> Products
>> MITSUBISHI
>> Servo driver/Servo motor
>> MR-H series
>> MR-H100TN | MITSUBISHI Servo amplifier MR-H100TN
MR-H100TN | MITSUBISHI Servo amplifier MR-H100TN
MITSUBISHI MR-H100TN Manual And Instructions
MR-H100TN datasheetPDF datasheet
MR-H100TN Instruction manual
MITSUBISHI MR-H100TN Product information and technical parameters：
Brand: MITSUBISHI
Name: Servo amplifier
Model: MR-H100TN
Drive: MR-H_ACN series CC-LINK features.
Rated output: 1.0KW.
The test system is composed of two parts, namely, the servo driver, the motor system and the host computer.
The host computer sends the speed command signal to the servo driver,
Servo drives start to run in accordance with the instructions.
In the course of operation, the running data of the servo system is collected by the host computer and the data acquisition circuit,
And carries on the preservation, the analysis and the display to the data. Because the motor is not loaded in this test system,
So compared with the previous two kinds of testing systems, the system has a relatively small volume,
And the measurement and control circuit of the system is relatively simple,
But it also makes the system can not simulate the actual operation of the servo drive.
Usually, such testing system is only used to test the rotational speed and angular displacement of the tested system under no-load condition,
And can not carry on the comprehensive and accurate test to the servo drive.
...More relevant models >>>>
MR-H100TN datasheetPDF datasheet
MR-H100TN Instruction manual
MITSUBISHI MR-H100TN Product information and technical parameters：
Brand: MITSUBISHI
Name: Servo amplifier
Model: MR-H100TN
Drive: MR-H_ACN series CC-LINK features.
Rated output: 1.0KW.
The test system is composed of two parts, namely, the servo driver, the motor system and the host computer.
The host computer sends the speed command signal to the servo driver,
Servo drives start to run in accordance with the instructions.
In the course of operation, the running data of the servo system is collected by the host computer and the data acquisition circuit,
And carries on the preservation, the analysis and the display to the data. Because the motor is not loaded in this test system,
So compared with the previous two kinds of testing systems, the system has a relatively small volume,
And the measurement and control circuit of the system is relatively simple,
But it also makes the system can not simulate the actual operation of the servo drive.
Usually, such testing system is only used to test the rotational speed and angular displacement of the tested system under no-load condition,
And can not carry on the comprehensive and accurate test to the servo drive.
For MR-J2S-700A (4) /CP/CL or less.
Encoder set for HC-SFS; HC-LFS; HC-RFS; HC-UFS2000r/min; HA-LFS servo motor.
IP67; IP65. Motor series: medium inertia, medium capacity.
Using a serial absolute / incremental encoder.
Rated output power: 7.0kw.
Rated speed: 2000rpm.
With the brake: without.
Shaft end: straight shaft MITSUBISHI MR-H100TN.
The rotor of AC servo motor is usually made of squirrel cage, but in order to make the servo motor has a wide range of speed regulation, linear mechanical properties,
Without the "rotation" phenomenon and the performance of the fast response, it is compared with the ordinary motor,
The two characteristics of rotor resistance and moment of inertia should be provided MR-H100TN
At present, there are two kinds of rotor structure, one is the squirrel cage rotor, which is made of conductive material with high resistivity,
In order to reduce the moment of inertia of the rotor, the rotor is slender MITSUBISHI MR-H100TN. Motor series: medium inertia, medium capacity.
Using a serial absolute / incremental encoder.
Rated output power: 1.0kw.
Rated speed: 3000rpm.
With a brake band.
Shaft end: straight shaft MITSUBISHI MR-H100TN.
When the AC servo motor has no control voltage, only the pulsating magnetic field generated by the excitation winding is generated in the stator, and the rotor is still not moving.
When the control voltage is controlled, a rotating magnetic field is generated in the stator, and the rotor rotates in the direction of the rotating magnetic field,
In the case of constant load, the speed of the motor varies with the size of the control voltage,
When the phase of the control voltage is reversed, the servo motor will reverse.Drive unit 200VAC/400VAC level.
MITSUBISHI motor general AC servo amplifier MELSERVO-J3 series.
Need conversion unit MR-J3-CR55K) supporting the use of.
Rated output: 45kw.
Interface type: SSCNET type III fiber communication.
Power specification: three phase AC400V.
High speed serial communication between the SSCNET and the servo amplifier by using the fastest up to 0.44ms communication cycle,
A fully synchronous control system can be constructed.
It is only necessary to insert the special optical fiber into the joint to form SSCNET III network, which greatly reduces the wiring work and reduces the possibility of false wiring.
Due to the adoption of the optical fiber commmunication, the anti noise ability can be greatly improved and the long distance wiring of 50 meters (maximum 800 meters x 16 axes) can be realized MR-H100TN.
A servo amplifier to meet the full closed loop control function MR-J3-B-RJ006.
Suitable foor mechanical servo optimization and adjustment!
More advanced optimization adjustment function and control function to maximize mechanical properties MR-H100TN.
Encoder set for HC-SFS; HC-LFS; HC-RFS; HC-UFS2000r/min; HA-LFS servo motor.
IP67; IP65. Motor series: medium inertia, medium capacity.
Using a serial absolute / incremental encoder.
Rated output power: 7.0kw.
Rated speed: 2000rpm.
With the brake: without.
Shaft end: straight shaft MITSUBISHI MR-H100TN.
The rotor of AC servo motor is usually made of squirrel cage, but in order to make the servo motor has a wide range of speed regulation, linear mechanical properties,
Without the "rotation" phenomenon and the performance of the fast response, it is compared with the ordinary motor,
The two characteristics of rotor resistance and moment of inertia should be provided MR-H100TN
At present, there are two kinds of rotor structure, one is the squirrel cage rotor, which is made of conductive material with high resistivity,
In order to reduce the moment of inertia of the rotor, the rotor is slender MITSUBISHI MR-H100TN. Motor series: medium inertia, medium capacity.
Using a serial absolute / incremental encoder.
Rated output power: 1.0kw.
Rated speed: 3000rpm.
With a brake band.
Shaft end: straight shaft MITSUBISHI MR-H100TN.
When the AC servo motor has no control voltage, only the pulsating magnetic field generated by the excitation winding is generated in the stator, and the rotor is still not moving.
When the control voltage is controlled, a rotating magnetic field is generated in the stator, and the rotor rotates in the direction of the rotating magnetic field,
In the case of constant load, the speed of the motor varies with the size of the control voltage,
When the phase of the control voltage is reversed, the servo motor will reverse.Drive unit 200VAC/400VAC level.
MITSUBISHI motor general AC servo amplifier MELSERVO-J3 series.
Need conversion unit MR-J3-CR55K) supporting the use of.
Rated output: 45kw.
Interface type: SSCNET type III fiber communication.
Power specification: three phase AC400V.
High speed serial communication between the SSCNET and the servo amplifier by using the fastest up to 0.44ms communication cycle,
A fully synchronous control system can be constructed.
It is only necessary to insert the special optical fiber into the joint to form SSCNET III network, which greatly reduces the wiring work and reduces the possibility of false wiring.
Due to the adoption of the optical fiber commmunication, the anti noise ability can be greatly improved and the long distance wiring of 50 meters (maximum 800 meters x 16 axes) can be realized MR-H100TN.
A servo amplifier to meet the full closed loop control function MR-J3-B-RJ006.
Suitable foor mechanical servo optimization and adjustment!
More advanced optimization adjustment function and control function to maximize mechanical properties MR-H100TN.
...More relevant models >>>>
Last one: 
next one: Related download