Home
>> Products
>> MITSUBISHI
>> Touch Screen
>> GOT1000 series touch screen
>> GT15 touch screen
>> GT1550-QLBD | MITSUBISHI 5.7 Inch Touch Screen GT1550-QLBD
GT1550-QLBD | MITSUBISHI 5.7 Inch Touch Screen GT1550-QLBD
MITSUBISHI GT1550-QLBD Manual And Instructions
GT1550-QLBD datasheetPDF datasheet
GT1550-QLBD MES Interface Function Manual
GT1550-QLBD Gateway Functions Manual
GT1550-QLBD Extended/Option Functions Manual
GT1550-QLBD Mitsubishi plc ConnectionsConnection Manual
GT1550-QLBD Connection Manual
GT1550-QLBD User's Manual
MITSUBISHI GT1550-QLBD Product information and technical parameters：
Brand: MITSUBISHI
Name: 5.7 Inch Touch Screen
Model: GT1550-QLBD
A series of high performance models that are widely used in network or single machine work environments.
Screen size: 5.7 inches.
Display color: monochrome.
Mounting type: panel mounting type.
Resolution: QVGA (320 x 240).
Display device: STN monochrome.
Host frame color: black.
Power type: DC24V.
Communication interface: with built-in RS-422.
Ideal model for high performance in a network or independent operation environment.
User storage capacity: 9MB (GT15__-VNB_:5MB).
Device USB port.
Standard RS-232 interface.
Support video /RGB unit.
If the capacitive touch screen is in the middle of the operation, the display resolution or display mode of the touch screen is changed again,
Or the refresh rate of the touch screen controller is adjusted by itself, and the cursor and the touch point can not be felt when the cursor is not corresponding to the touch point,
Must be re calibrated to the touch screen system.
In order to ensure the normal operation of the touch screen system, in addition to ensure the proper installation of the system software,
Must also remember that in a host do not install two or more than two kinds of touch screen driver,
This will cause the system to run in conflict, so that the touch screen system can not be used properly.
...More relevant models >>>>
GT1550-QLBD datasheetPDF datasheet
GT1550-QLBD MES Interface Function Manual
GT1550-QLBD Gateway Functions Manual
GT1550-QLBD Extended/Option Functions Manual
GT1550-QLBD Mitsubishi plc ConnectionsConnection Manual
GT1550-QLBD Connection Manual
GT1550-QLBD User's Manual
MITSUBISHI GT1550-QLBD Product information and technical parameters：
Brand: MITSUBISHI
Name: 5.7 Inch Touch Screen
Model: GT1550-QLBD
A series of high performance models that are widely used in network or single machine work environments.
Screen size: 5.7 inches.
Display color: monochrome.
Mounting type: panel mounting type.
Resolution: QVGA (320 x 240).
Display device: STN monochrome.
Host frame color: black.
Power type: DC24V.
Communication interface: with built-in RS-422.
Ideal model for high performance in a network or independent operation environment.
User storage capacity: 9MB (GT15__-VNB_:5MB).
Device USB port.
Standard RS-232 interface.
Support video /RGB unit.
If the capacitive touch screen is in the middle of the operation, the display resolution or display mode of the touch screen is changed again,
Or the refresh rate of the touch screen controller is adjusted by itself, and the cursor and the touch point can not be felt when the cursor is not corresponding to the touch point,
Must be re calibrated to the touch screen system.
In order to ensure the normal operation of the touch screen system, in addition to ensure the proper installation of the system software,
Must also remember that in a host do not install two or more than two kinds of touch screen driver,
This will cause the system to run in conflict, so that the touch screen system can not be used properly.
Cable length: 3 meters.
QnACPU GOT.
RS-422 conversion (FA-CNV / CBL) cable GOT.
The serial communication module GOT.
The peripheral machine connection module (AJ65BT-G4-S3) GOT.
[D-sub 25 pin loose line (row 5 pin interface terminal)].
GT2103-PMBD does not support Q00JCPU, Q00CPU, CPU Q01CPU direct connection MITSUBISHI GT1550-QLBD.
Applicable model: GT21. Cable length: 30m.
For connection between QnA/A/FXCPU (D-SUB25 pin connector) and GOT GT1550-QLBD
Connection between serial communication unit (AJ71QC24-R4) and GOT.
Applicable models: GT10, GT21. Series Name: A975GOT.
Size: 10 inches.
Resolution: 600 * 480.
Display equipment: high brightness TFT color display.
Display color: 16 color.
Power supply: DC24V.
Memory card: 1M MITSUBISHI GT1550-QLBD.
Man machine interface is the interface between man and machine in the field of information exchange and function contact or influence,
Information exchange, functional contact or mutual influence, the hard contact and soft touch of a person and machine,
This interface includes not only the direct contact point line side,
It also includes the function of remote information transmission and control MITSUBISHI GT1550-QLBD.
The man-machine interface is the central link in the man-machine system,
Mainly from the safety engineering branch of the safety ergonomics to study and put forward the basis for the solution,
And over the safety engineering equipment engineering, safety management engineering and safety systems engineering to study the specific solutions and measures to the safety of human computer science and technology.
It realizes the transformation between the internal form of information and the acceptable form of human being. 48MB extended memory.
Applicable model: GT15. Series: multimedia and advanced features and features of a variety of high-performance models.
Screen size: 15 inches.
Display color: 256 color or more color.
Installation type: compatible with multimedia and video /RGB.
Resolution: XGA (1024 x 768).
Display device: TFT color (high brightness, wide viewing angle).
Host frame color: black.
Power type: AC100~240V.
Communication interface: with built-in RS-422.
High performance models with multimedia and advanced features and functionality (including embedded communications capabilities).
User storage capacity: 15MB (GT16__-VNB__:11MB).
With HOST USB and device USB port.
Standard Ethernet, RS-422/485 and RS-232 ports.
Support multimedia and video /RGB units.
Analog touch panel.
Do not let the touch screen surface with water drops or other soft things stick to the surface,
Otherwise, the touch screen is easy to mistake that there is a hand touch caused by surface acoustic wave screen is not allowed.
In addition to cleaning the dirt on the surface of the touch screen,
You can use a soft dry cloth or a cleaning agent to clean out the center of the screen carefully,
Or use a dry soft cloth dipped in industrial alcohol or glass cleaning fluid to clean the touch screen surface.
Touch screen response is slow if you use a hand or other touch to touch the surface acoustic wave touch screen,
This shows that it is likely that the touch screen system has been obsolete, the internal clock frequency is too low,
Or because there is water in the surface of the touch screen to make the touch screen mobile, rapid response recovery,
To replace or upgrade the system mustt, or use dry cloth touch screen on the surface of the water GT1550-QLBD.
If the user is operating the touch screen, the direction of the touch move is to the left,
But the cursor of the system moves to the right,
The failure may be due to the conneection of the control box and the touch screen connected to the connector or the touch screen,
Users as long as the direction of the re exchange of it GT1550-QLBD.
QnACPU GOT.
RS-422 conversion (FA-CNV / CBL) cable GOT.
The serial communication module GOT.
The peripheral machine connection module (AJ65BT-G4-S3) GOT.
[D-sub 25 pin loose line (row 5 pin interface terminal)].
GT2103-PMBD does not support Q00JCPU, Q00CPU, CPU Q01CPU direct connection MITSUBISHI GT1550-QLBD.
Applicable model: GT21. Cable length: 30m.
For connection between QnA/A/FXCPU (D-SUB25 pin connector) and GOT GT1550-QLBD
Connection between serial communication unit (AJ71QC24-R4) and GOT.
Applicable models: GT10, GT21. Series Name: A975GOT.
Size: 10 inches.
Resolution: 600 * 480.
Display equipment: high brightness TFT color display.
Display color: 16 color.
Power supply: DC24V.
Memory card: 1M MITSUBISHI GT1550-QLBD.
Man machine interface is the interface between man and machine in the field of information exchange and function contact or influence,
Information exchange, functional contact or mutual influence, the hard contact and soft touch of a person and machine,
This interface includes not only the direct contact point line side,
It also includes the function of remote information transmission and control MITSUBISHI GT1550-QLBD.
The man-machine interface is the central link in the man-machine system,
Mainly from the safety engineering branch of the safety ergonomics to study and put forward the basis for the solution,
And over the safety engineering equipment engineering, safety management engineering and safety systems engineering to study the specific solutions and measures to the safety of human computer science and technology.
It realizes the transformation between the internal form of information and the acceptable form of human being. 48MB extended memory.
Applicable model: GT15. Series: multimedia and advanced features and features of a variety of high-performance models.
Screen size: 15 inches.
Display color: 256 color or more color.
Installation type: compatible with multimedia and video /RGB.
Resolution: XGA (1024 x 768).
Display device: TFT color (high brightness, wide viewing angle).
Host frame color: black.
Power type: AC100~240V.
Communication interface: with built-in RS-422.
High performance models with multimedia and advanced features and functionality (including embedded communications capabilities).
User storage capacity: 15MB (GT16__-VNB__:11MB).
With HOST USB and device USB port.
Standard Ethernet, RS-422/485 and RS-232 ports.
Support multimedia and video /RGB units.
Analog touch panel.
Do not let the touch screen surface with water drops or other soft things stick to the surface,
Otherwise, the touch screen is easy to mistake that there is a hand touch caused by surface acoustic wave screen is not allowed.
In addition to cleaning the dirt on the surface of the touch screen,
You can use a soft dry cloth or a cleaning agent to clean out the center of the screen carefully,
Or use a dry soft cloth dipped in industrial alcohol or glass cleaning fluid to clean the touch screen surface.
Touch screen response is slow if you use a hand or other touch to touch the surface acoustic wave touch screen,
This shows that it is likely that the touch screen system has been obsolete, the internal clock frequency is too low,
Or because there is water in the surface of the touch screen to make the touch screen mobile, rapid response recovery,
To replace or upgrade the system mustt, or use dry cloth touch screen on the surface of the water GT1550-QLBD.
If the user is operating the touch screen, the direction of the touch move is to the left,
But the cursor of the system moves to the right,
The failure may be due to the conneection of the control box and the touch screen connected to the connector or the touch screen,
Users as long as the direction of the re exchange of it GT1550-QLBD.
...More relevant models >>>>
Last one: MITSUBISHI 5.7 Inch Touch Screen GT1555-QSBD
next one: MITSUBISHI 15 Inch Touch Screen GT1685M-STBA
Related download