Home
>> Products
>> MITSUBISHI
>> Touch Screen
>> Touch screen accessories
>> GOT1000 touch screen accessories
>> GT05-MEM-ADPC | MITSUBISHI Memory card adapter GT05-MEM-ADPC
GT05-MEM-ADPC | MITSUBISHI Memory card adapter GT05-MEM-ADPC
MITSUBISHI GT05-MEM-ADPC Manual And Instructions
GT05-MEM-ADPC datasheetPDF datasheet
GT05-MEM-ADPC User's Manual
MITSUBISHI GT05-MEM-ADPC Product information and technical parameters：
Brand: MITSUBISHI
Name: Memory card adapter
Model: GT05-MEM-ADPC
The CF card, memory card adapter (TYPEIII).
Applicable models: GT16, GT15, GT11, HandyGOT. "
...More relevant models >>>>
GT05-MEM-ADPC datasheetPDF datasheet
GT05-MEM-ADPC User's Manual
MITSUBISHI GT05-MEM-ADPC Product information and technical parameters：
Brand: MITSUBISHI
Name: Memory card adapter
Model: GT05-MEM-ADPC
The CF card, memory card adapter (TYPEIII).
Applicable models: GT16, GT15, GT11, HandyGOT. "
A series of high performance models that are widely used in network or single machine work environments.
Screen size: 5.7 inches.
Display color: 256 color or more color.
Mounting type: panel mounting type.
Resolution: QVGA (320 x 240).
Display device: TFT color (high brightness, wide viewing angle).
Host frame color: black MITSUBISHI GT05-MEM-ADPC.
Power type: DC24V.
Communication interface: with built-in RS-422 GT05-MEM-ADPC
Ideal model for high performance in a network or independent operation environment.
User storage capacity: 9MB (GT15__-VNB_:5MB).
Device USB port.
Standard RS-232 interface.
Support video /RGB unit.
If the capacitive touch screen is in the middle of the operation, the display resolution or display mode of the touch screen is changed again,
Or the refresh rate of the touch screen controller is adjusted by itself, and the cursor and the touch point can not be felt when the cursor is not corresponding to the touch point,
Must be re calibrated to the touch screen system MITSUBISHI GT05-MEM-ADPC.
In order to ensure the normal operation of the touch screen system, in addition to ensure the proper installation of the system software,
Must also remember that in a host do not install two or more than two kinds of touch screen driver,
This will cause the system to run in conflict, so that the touch screen system can not be used properly MITSUBISHI GT05-MEM-ADPC. Bus cables used for GOT1000 to replace the ferrite cores used in the existing GOT-A900 bus cables.
Applicable models: GT16, GT15, GT11, GT27, GT25. 1 channels for analog RGB input.
Applicable model: GT15. For video input (NTSC/PAL) 4ch/ analog 1ch RGB input.
Applicable model: GT27. Cable length: 13m.
The connection between the CC-LINK interface unit and the smart GOT.
Applicable model: HandyGOT. Cable length: 3m.
The connection between the FXCPU communication function extension board (D-SUB9 pin connector) and the GOT/ personal computer (D-SUB9) (GTSoftGOT100 pin) GT05-MEM-ADPC.
The connection between the FXCPU communication function adapter (D-SUB9 pin connector) and the GOT.
For personal computer (screen design software) (D-SUB9 pin, the mother''s head) annd GOT (D-SUB9 needle, the mother of the head) of the connection between GT05-MEM-ADPC.
Applicable models: GT16, GT15, GT11, HandyGOT, GT10, GT27, GT25, GT23,, GT21.
Screen size: 5.7 inches.
Display color: 256 color or more color.
Mounting type: panel mounting type.
Resolution: QVGA (320 x 240).
Display device: TFT color (high brightness, wide viewing angle).
Host frame color: black MITSUBISHI GT05-MEM-ADPC.
Power type: DC24V.
Communication interface: with built-in RS-422 GT05-MEM-ADPC
Ideal model for high performance in a network or independent operation environment.
User storage capacity: 9MB (GT15__-VNB_:5MB).
Device USB port.
Standard RS-232 interface.
Support video /RGB unit.
If the capacitive touch screen is in the middle of the operation, the display resolution or display mode of the touch screen is changed again,
Or the refresh rate of the touch screen controller is adjusted by itself, and the cursor and the touch point can not be felt when the cursor is not corresponding to the touch point,
Must be re calibrated to the touch screen system MITSUBISHI GT05-MEM-ADPC.
In order to ensure the normal operation of the touch screen system, in addition to ensure the proper installation of the system software,
Must also remember that in a host do not install two or more than two kinds of touch screen driver,
This will cause the system to run in conflict, so that the touch screen system can not be used properly MITSUBISHI GT05-MEM-ADPC. Bus cables used for GOT1000 to replace the ferrite cores used in the existing GOT-A900 bus cables.
Applicable models: GT16, GT15, GT11, GT27, GT25. 1 channels for analog RGB input.
Applicable model: GT15. For video input (NTSC/PAL) 4ch/ analog 1ch RGB input.
Applicable model: GT27. Cable length: 13m.
The connection between the CC-LINK interface unit and the smart GOT.
Applicable model: HandyGOT. Cable length: 3m.
The connection between the FXCPU communication function extension board (D-SUB9 pin connector) and the GOT/ personal computer (D-SUB9) (GTSoftGOT100 pin) GT05-MEM-ADPC.
The connection between the FXCPU communication function adapter (D-SUB9 pin connector) and the GOT.
For personal computer (screen design software) (D-SUB9 pin, the mother''s head) annd GOT (D-SUB9 needle, the mother of the head) of the connection between GT05-MEM-ADPC.
Applicable models: GT16, GT15, GT11, HandyGOT, GT10, GT27, GT25, GT23,, GT21.
...More relevant models >>>>
Last one: 
next one: Related download