Home
>> Products
>> MITSUBISHI
>> FX series PLC
>> FX all modules and accessories
>> FX2N module
>> FX2N-48ER-UA1/UL | MITSUBISHI Relay output unit FX2N-48ER-UA1/UL
FX2N-48ER-UA1/UL | MITSUBISHI Relay output unit FX2N-48ER-UA1/UL
MITSUBISHI FX2N-48ER-UA1/UL Manual And Instructions
FX2N-48ER-UA1/UL datasheetPDF datasheet
MITSUBISHI FX2N-48ER-UA1/UL Product information and technical parameters：
Brand: MITSUBISHI
Name: Relay output unit
Model: FX2N-48ER-UA1/UL
Total input and output points: 48 points.
Input points: 24 points.
Output points: 24 points.
Output type: relay output.
Power supply voltage: AC100-240V.
Input signal voltage: AC100V.
8K capacity of the RAM memory, the maximum can be extended to 16K.
CPU arithmetic processing speed of 0.08 S/ basic instructions.
On the right side of the FX2N series can be connected to the input and output expansion modules and special function modules.
The basic unit is built in the 2 axis independent maximum 20kHz positioning function (transistor output type).
Quick disconnect the terminal block, which adopts excellent maintainability to quickly disconnect the terminal blocks, even if the cable is then replaced by the cable.
Clock function and hour meter function, all of the PLC FX2N has a real-time clock standard.
Continuous scanning function, to define the operation cycle for the application of the continuous scan time.
Input filter adjustment function, you can use the input filter to smooth the input signal (in the basic unit x000 to x017).
Note recording function, Component annotation can be recorded in the program register.
Online program editor, online change the program will not lose the working hours or stop production operation.
RUN/STOP switch, running on panel / stop switch easy to operate.
Remote maintenance, remote programming software can monitor, upload or uninstall programs and data via modem communications
Password protection, using a eight digit password to protect your program.
...More relevant models >>>>
FX2N-48ER-UA1/UL datasheetPDF datasheet
MITSUBISHI FX2N-48ER-UA1/UL Product information and technical parameters：
Brand: MITSUBISHI
Name: Relay output unit
Model: FX2N-48ER-UA1/UL
Total input and output points: 48 points.
Input points: 24 points.
Output points: 24 points.
Output type: relay output.
Power supply voltage: AC100-240V.
Input signal voltage: AC100V.
8K capacity of the RAM memory, the maximum can be extended to 16K.
CPU arithmetic processing speed of 0.08 S/ basic instructions.
On the right side of the FX2N series can be connected to the input and output expansion modules and special function modules.
The basic unit is built in the 2 axis independent maximum 20kHz positioning function (transistor output type).
Quick disconnect the terminal block, which adopts excellent maintainability to quickly disconnect the terminal blocks, even if the cable is then replaced by the cable.
Clock function and hour meter function, all of the PLC FX2N has a real-time clock standard.
Continuous scanning function, to define the operation cycle for the application of the continuous scan time.
Input filter adjustment function, you can use the input filter to smooth the input signal (in the basic unit x000 to x017).
Note recording function, Component annotation can be recorded in the program register.
Online program editor, online change the program will not lose the working hours or stop production operation.
RUN/STOP switch, running on panel / stop switch easy to operate.
Remote maintenance, remote programming software can monitor, upload or uninstall programs and data via modem communications
Password protection, using a eight digit password to protect your program.
Max input / output points: 14 points.
Supply voltage: 100 - 240VAC.
Input points: 8 points.
Output points: 6 points.
Output type: Transistor (source).
Power consumption (W): 6.5.
Weight (kg):0.22.
Size (WxHxD) mm:60x90x49.
Host has 10 points (6I/4O), 14 points (8I/6O), 20 points (12I/8O), 30 points (16I/14O) of 4 types MITSUBISHI FX2N-48ER-UA1/UL.
This type of PLC is mainly used in all of the digital input, digital output control point of the device FX2N-48ER-UA1/UL
Can be directly connected to the 220V city power, built-in 8K step EEPROM memory, no battery, easy to maintain.
The series transistor output (MT) of the PLC, can be output 2 100KHz pulse, direct drive servo or stepper motor.
The series PLC can not be brought with the expansion module, but can be installed by the BD board to extend a small amount of I/O MITSUBISHI FX2N-48ER-UA1/UL.
The series 1N through the installation of BD series PLC board, can achieve RS232, RS485, RS422 communication. Needle number: 20.
Specification: loose wire connector, 5 sets (0.3mm 2). Max input / output points: 40 points.
Power supply voltage: DC24V.
Input points: 24 points.
Output points: 16 points.
Output type: transistor MITSUBISHI FX2N-48ER-UA1/UL.
Power consumption (W): 32.
Weight (kg):0.65.
Size (WxHxD) mm:130x90x75.
FX1N series is a very powerful micro PLC, can be extended to up to 128 I/O points,
And can increase the special function module or the expansion board.
Communication and data link function options make FX1N in the volume, communication and special function modules and other important applications is very perfect.
A PLC unit can output 2 100KHz pulses at the same time,
PLC is equipped with 7 special positioning instructions,
Including zero return, absolute position readout, absolute or relative drive, and special pulse output control. Analog output expansion board (1 channel).Analog input points: 4.
Analog output points: 1 points.
Analog input and output expansion module.
With 4CH analog input and 1CH analog output.
With -100mV~100mV micro voltage input range, annd therefore do not need a signal converter, etc FX2N-48ER-UA1/UL. .
Resolution of 15 bit binary + symbol 14bit, 1bit binary + symbol 1bit high precision analog input and output modules.
Each channel can be used for different input ranges.
Built in iinput filter adjustment function, internal operation function, proportion function FX2N-48ER-UA1/UL.
Connect FX3UC, FX3GC, you need to use FX2NC-CNV-IF or FX3UC-1PS-5V.
Supply voltage: 100 - 240VAC.
Input points: 8 points.
Output points: 6 points.
Output type: Transistor (source).
Power consumption (W): 6.5.
Weight (kg):0.22.
Size (WxHxD) mm:60x90x49.
Host has 10 points (6I/4O), 14 points (8I/6O), 20 points (12I/8O), 30 points (16I/14O) of 4 types MITSUBISHI FX2N-48ER-UA1/UL.
This type of PLC is mainly used in all of the digital input, digital output control point of the device FX2N-48ER-UA1/UL
Can be directly connected to the 220V city power, built-in 8K step EEPROM memory, no battery, easy to maintain.
The series transistor output (MT) of the PLC, can be output 2 100KHz pulse, direct drive servo or stepper motor.
The series PLC can not be brought with the expansion module, but can be installed by the BD board to extend a small amount of I/O MITSUBISHI FX2N-48ER-UA1/UL.
The series 1N through the installation of BD series PLC board, can achieve RS232, RS485, RS422 communication. Needle number: 20.
Specification: loose wire connector, 5 sets (0.3mm 2). Max input / output points: 40 points.
Power supply voltage: DC24V.
Input points: 24 points.
Output points: 16 points.
Output type: transistor MITSUBISHI FX2N-48ER-UA1/UL.
Power consumption (W): 32.
Weight (kg):0.65.
Size (WxHxD) mm:130x90x75.
FX1N series is a very powerful micro PLC, can be extended to up to 128 I/O points,
And can increase the special function module or the expansion board.
Communication and data link function options make FX1N in the volume, communication and special function modules and other important applications is very perfect.
A PLC unit can output 2 100KHz pulses at the same time,
PLC is equipped with 7 special positioning instructions,
Including zero return, absolute position readout, absolute or relative drive, and special pulse output control. Analog output expansion board (1 channel).Analog input points: 4.
Analog output points: 1 points.
Analog input and output expansion module.
With 4CH analog input and 1CH analog output.
With -100mV~100mV micro voltage input range, annd therefore do not need a signal converter, etc FX2N-48ER-UA1/UL. .
Resolution of 15 bit binary + symbol 14bit, 1bit binary + symbol 1bit high precision analog input and output modules.
Each channel can be used for different input ranges.
Built in iinput filter adjustment function, internal operation function, proportion function FX2N-48ER-UA1/UL.
Connect FX3UC, FX3GC, you need to use FX2NC-CNV-IF or FX3UC-1PS-5V.
...More relevant models >>>>
Last one: MITSUBISHI Relay output unit FX2N-48ER
next one: MITSUBISHI Transistor output unit FX2N-32ET
Related download