MITSUBISHI
Home >> Download >> MITSUBISHI >> Catalog Download >> MITSUBISHI AJ65SBTB1-32TE1 datasheet PDF catalog AJ65SBTB1-32TE1 PDF datasheet

MITSUBISHI AJ65SBTB1-32TE1 datasheet PDF catalog AJ65SBTB1-32TE1 PDF datasheet

Brand: MITSUBISHI
Product model: AJ65SBTB1-32TE1
Name: Transistor output module
Sort: PDF datasheet
File language: English
File size: 8.82MB
8 slot, PID special substrate.
When the programmer input programinto the user program memory,
Then CPU according to the function of the system (the system program memory to explain the compiler),
Translate the user program into PLC internally recognized by the user to compile the program.
Relay output interface circuit of PLC
Working process: when the internal circuit output digital signal 1,
There is a current flowing through, the relay coil has a current, and then the normally open contact is closed,
Provide load current and voltage AJ65SBTB1-32TE1 datasheet PDF catalog AJ65SBTB1-32TE1 PDF datasheet AJ65SBTB1-32TE1
When the internal circuit outputs a digital signal 0, there is no current flowing through it,
The relay coil does not have a current, and the normally open contact is broken off,
A current or voltage that is disconnected from the load AJ65SBTB1-32TE1 datasheet PDF catalog AJ65SBTB1-32TE1 PDF datasheet.
It is through the output interface circuit to the internal digital circuit into a signal to make the load action or not action.
I/O points is an important indicator of PLC.
Reasonable selection of I/O points can not only satisfy the control requirements of the system,
And the total investment of the system is the lowest AJ65SBTB1-32TE1 datasheet PDF catalog AJ65SBTB1-32TE1 PDF datasheet.
The input and output points and types of PLC should be determined according to the analog quantity and switch quantity of the controlled object,
Generally an input / output element to take up an input / output point.
Taking into account the future adjustment and expansion,
In general should be estimated on the total number of points plus the amount of spare 20%~30%.
The following describes the centralized control system I/O points of the estimate. Analog channel: 8 channels.
Input / output (resolution): 0 ~ 4000.
Conversion speed: 100ms/8 channel.
Analog module installation.
Power supply: DC24V.
According to the control requirements of the system, using the appropriate design method to design MITSUBISHI PLC program.
Procedures to meet the requirements of system control as the main line,
Write one by one to achieve the control function or the sub task of the program,
Gradually improve the functions specified by the system.
MITSUBISHI PLC detection, fault diagnosis and display and other procedures.
These procedures are relatively independent, generally in the basic completion of the program design and then add.
Hardware simulation method is to use a number of hardware equipment to simulate the generation of the signal,
The signals are connected to the input end of the PLC system in a hard wired way, and the timeliness is strong.
Software simulation metthod is in the MITSUBISHI PLC in the preparation of a set of simulation program,
The simulation provides the field signal, which is simple and easy to operate, but it is not easy too guarantee the timeliness AJ65SBTB1-32TE1 datasheet PDF catalog AJ65SBTB1-32TE1 PDF datasheet AJ65SBTB1-32TE1 datasheet PDF catalog AJ65SBTB1-32TE1 PDF datasheet.
Simulation of the process of debugging, debugging method can be used to segment, and the monitoring function of programmer.
Related products
MITSUBISHI
Transistor output module
AJ65SBTB1-8T
MITSUBISHI Transistor output module AJ65SBTB1-8T
Output type: transistor output, drain type. O
MITSUBISHI
Input module
AJ65SBTB3-16KD
MITSUBISHI Input module AJ65SBTB3-16KD
Input type: DC input, positive pulic end / n
MITSUBISHI
Input module
AJ65SBTB1-16D1
MITSUBISHI Input module AJ65SBTB1-16D1
Input type: DC input, positive pulic end / n