MITSUBISHI Q00UJCPU-S8 MELSAP-L Manual Q00UJCPU-S8 Programming Manual

SRAM memory card.
RAM capacity: 128KB. Board module installation location: QS series power module mounting slot.
Suitable substrate module: QS034B.
Input power: AC100~120V.
Security PLC (secure programmable system) refers to the self or external components or the implementation of the failure of the agency,
Can still respond to and promptly cut off the output of the programmable system Q00UJCPU-S8 MELSAP-L Manual Q00UJCPU-S8 Programming Manual Q00UJCPU-S8
Different from ordinary PLC, security PLC not only can provide the function of ordinary PLC,
Safe control function can be realized,
Meet the requirements of the ISO 13849-1 EN and IEC 61508 control system safety related component standards.
PLC security market mainstream has oilz (Pilz) PSS 3000, PSS 4000,
PSS 4000 in addition to the security process can also be processed outside the standard control procedures Q00UJCPU-S8 MELSAP-L Manual Q00UJCPU-S8 Programming Manual.
All the components in the security PLC adopt the redundancy structure,
Two processor processing for cross detection,
The processing results of each processor are stored in their respective memory,
Output is only when the processing result is in full agreement,
If any inconsistency occurs during the process, the system is immediately shut down Q00UJCPU-S8 MELSAP-L Manual Q00UJCPU-S8 Programming Manual. Master / local station sharing.
Corresponding Ver2 CC-Link.
I/O control in the first class of open field network module.
CC-Link based on reliable field bus technology,
Able to transmit large number of bits data (such as ON/OFF information) and word data (such as analog information).
Consistency of CC-Link to maintain loop transmission,
And the cycle of transmission and information (instantaneous transmission) communication separately, so as to ensure the timeliness of.
Even if the information reaches saturation, it will not affect the link scan time.
The QJ61BT11N module supports CC-Link version 1 and version 2, which can be used as a local station or master station module."Maximum control axis: 16 axis.
Connection mode with servo amplifier: IE CC-Link field network connection type.
The maximum distance between the drive units: 100m.
Operation cycle: 0.88ms, 1.77ms, 3.55ms.
Interpolation function: linear interpolation (maximum 4 axis), 2 axis arc interpolation.
Color signal: 4 points.
Color detecting set: 16 set.
Motion control into CC-LinkIE network.
Positioning control, synchronization control and cam control can be easily carried out by the simple parameter setting and the starting of the sequential program.
QD77GF can be used as the main station of CC-LinkIE network.
Communication between 1 network implementation and servo amplifier, field device (remote I/O, sensor, etc.).
Note 1:QD77G only the master station can use the bus shape, star. 1 networks can connect up to 104 units from the device.
Even the long distance wiring can be flexible.
The use of fiber optic cable, with high speed, high performance, high reliability of the servo system controller network.
In addition to the traditional positioning control, but also to support speed / torque control and synchronous control.
Use simple movement module setup tool",
Can easily perform positioning settings, monitoring and debugging, etc..
In addition, the data can be collected and displayed synchronously with the motion controller.
Support compprehensive, wiring flexible IE CC-Link field network Q00UJCPU-S8 MELSAP-L Manual Q00UJCPU-S8 Programming Manual.
This module can be used as the main station of IE CC-Link field network (equivalent to QJ71GF11-T2),
And still retains the function of ssimple motion module Q00UJCPU-S8 MELSAP-L Manual Q00UJCPU-S8 Programming Manual.
Therefore, flexible connection display (GOT), remote I/O, frequency converter and other equipment, flexible construction system. "