MITSUBISHI GT2715-XTBA Hardware Manual GT2715-XTBA User's Manual

For GT1030/GT1020 (used for operating system project data transfer) without power supply.
Applicable model: GT10. For video input (NTCS/PAL) 4 channel / RGB input 1 channel composite input.
Applicable model: GT15. For the graphic operation terminal on the back of the extra CF port (B disk).
Applicable models: GT16, GT15 GT2715-XTBA Hardware Manual GT2715-XTBA User's Manual. Protective film for 15 inch screen GT2715-XTBA
Scrub, 5.
Applicable model: GT16. Cable length: 10m.
For connection between FXCPU (MINI-DIN8 pin connector) and GOT.
Connection between FXCPU communication function extension board (MINI-DIN8 pin connector) and GOT.
Applicable models: GT16, GT15, GT11, HandyGOT, GT10, GT27, GT25, GT23,, GT21. A series of high performance models that are widely used in network or single machine work environments GT2715-XTBA Hardware Manual GT2715-XTBA User's Manual.
Screen size: 8.4 inches.
Display color: 256 color or more color.
Mounting type: panel mounting type.
Resolution: VGA (640 x 480).
Display device: TFT color (high brightness, wide viewing angle).
Host frame color: black.
Power type: DC24V.
Communication interface: with built-in RS-422.
Ideal model for high performance in a network or independent operation environment GT2715-XTBA Hardware Manual GT2715-XTBA User's Manual.
User storage capacity: 9MB (GT15__-VNB_:5MB).
Device USB port.
Standard RS-232 interface.
Support video /RGB unit.
If the capacitive touch screen is in the middle of the operation, the display resolution or display mode of the touch screen is changed again,
Or the refresh rate of the touch screen controller is adjusted by itself, and the cursor and the touch point can not be felt when the cursor is not corresponding to the touch point,
Must be re calibrated to the touch screen system.
In order to ensure the normal operation of the touch screen system, in addition to ensure the proper installation of the system software,
Must also remember that in a host do not install two or more than two kinds of touch screen driver,
This will cause the system to run in conflict, so that the touch screen system can not be used properly. Function: high performance and low price in the middle end model.
Picture size: 12.1 inches.
Resolution: SVGA.
Display: TFT color.
Panel color: white.
Power type: AC100~240V.
Communication interface: CC-Link IE network communication module set.
The highest level model with multi touch and gesture features.
Specification rich, design at ease.
GT27 standard supports SD memory card and standard equipped with Ethernet, RS-232, RS-422/485, host/device USB interface.
Even in the log, script, alarm, soft component data transmission, such as high load processing period, but also to achieve smooth operation of the screen.
In addition, also supports video, animation playback, video input and RGB input and output, can use all the features of GOT2000.
Can be programmed CPU and other procedures, parameters, such as data storage (backup) to the SD GOT memory card, USB memory.
When the programmable controller fails, batch write back (recovery) program.
1, the human body sensor
People will be able to automatically detect and display the picture.
2, USB interface: device USB (Mini-B USB)
Can connect to the computer to transfer data.
3, USB interface: host USB (USB-A)
GOT data can be transmitted through the USB memory or read log data and other data,
Can also be connected to the USB mouse, keyboard use.
4, the extension of the interface
Communication module and optional module can be installed.
5, Etheernet interface
Up to 4 different manufacturers can be connected to the FA machine GT2715-XTBA Hardware Manual GT2715-XTBA User's Manual.
6, RS-232 interface
Can connect all kinds of FA machine, bar code reader, serial printer.
7, RS-422/485 interfface
Can be connected to a variety of FA machines, bar code reader GT2715-XTBA Hardware Manual GT2715-XTBA User's Manual.
8, SD memory card slot
Can save alarm and log data, such as a large number of data.